:: Products - Cone Pulley Heavy Duty Lathe Machine
TECHNICAL DATA AND SPECIFICATIONS
FOR STANDARD MODEL VH-0, VH-1, VH-2, VH-3, VH-4, VH-5, VH-6, VH-7, VH-8.
STD C.H.
12” C.H.
Centre Height over flat bed ways :
267 m.m.
305 m.m.
Swing Over Bed :
525 m.m.
600 m.m.
Swing Over Cross Slide :
300 m.m.
375 m.m.
Swing In Gap :
830 m.m.
910 m.m.
Length of Gap in front of Face Plate :
200 m.m.
200 m.m.
Width of Bed : STANDARD 325 m.m. (13”) | OPTIONAL : 375 m.m. (15”)
MODEL
ADMIT
BETWEEN
CENTRES
LENGTH
OF BED
Floor Space
Occupied (m.m.)
Aprox. Weight
in kgs.
Aprox. Case
Dimensions
(m.m.)
Nett.
Gross
VH-0
525 m.m.
1675 m.m. (5’-6”)
2200 x 1450
1200
1500
2400 x 1300 x 1600
VH-1
1000 m.m.
2135 m.m. (7’)
2660 x 1450
1300
1700
2850 x 1300 x 1600
VH-2
1600 m.m.
2745 m.m. (9’)
3140 x 1450
1400
1900
3350 x 1300 x 1600
VH-3
1900 m.m.
3050 m.m. (10’)
3500 x 1450
1650
2200
3700 x 1300 x 1600
VH-4
2500 m.m.
3660 m.m. (12’)
4110 x 1450
1800
2400
4300 x 1300 x 1600
VH-5
3100 m.m.
4270 m.m. (14’)
4720 x 1450
2100
2700
5000 x 1300 x 1600
VH-6
3710 m.m.
4875 m.m. (16’)
5330 x 1450
2500
3200
5550 x 1300 x 1600
VH-7
4320 m.m.
5485 m.m. (18’)
5940 x 1450
2800
3600
6100 x 1300 x 1600
VH-8
4930 m.m.
6095 m.m. (20’)
6550 x 1450
3100
4000
6710 x 1300 x 1600
MAIN SPINDLE :
Spindle bore / Nose diameter X Threads:
Standard
: 51 m.m. / 74.3 m.m. X 6 TPI
OPTIONAL
: 76 .m.m / 102.85 m.m. X 6 TPI
OPTIONAL
: 101 .m.m / 131.45 m.m. X 6 TPI
Spindle Morse Taper
: MT-6
Spindle Adapter Morse Taper
: MT-4
Spindle Speeds Nos. / Range
: 8 / 28 to 520 R.P.M.
Spindle Drive Standard
: Flat Belt
OPTIONAL : V-Belt
Spindle Mounting Standard
: Split Bush Bearings
OPTIONAL : Taper Roller Bearings
STANDARD ACCESSORIES :
Flame Hardened bed ways,
Chuck back plate 1 no, centre adapter, Dead centres (MT - 4) 2 nos, Tool Post Spanner, Motor pulley, Thread dial indicator, chip tray, Nylone flat belt, Change gear set - 1 (For metric and inch both)
OPTIONAL ACCESSORIES :
Face plate, Carrier plate, steady rest, follow rest, Taper turning attachment, motorised coolant pump with tank and fittings, Rear tool post with extended cross slide, Norton gear box, Chuck back plates (Extra), V-Belt drive pullies in lieu of flat belt, main spindle mounted on taper roller bearings in lieu of bush bearings and Electricals (Motor, Switch, wirings, V-belts and fittings)
Nos. of Threads / Range
(Without norton Gearbox)
Metric
Inch
13 / 1 m.m. To 6 m.m. Pitch
19 /2 to 24 TPI
Nos. of Threads / Range
(For Fully norton Gearbox)
Metric
Inch
17 / 0.5 m.m. To 15 m.m. Pitch
40 / 2 to 60 TPI
FEEDS
Nos. of Feeds / Range
(Without norton Gearbox )
Longitudinal
Cross
19 / 0.165 To 1.996 m.m. / rev. of spindle
19 / 0.04 To 0.485 m.m. / rev. of spindle
Nos. of Feeds / Range
(For Fully norton Gearbox)
Longitudinal
Cross
40 / 0.066 to 2 m.m. / rev. of spindle
40 / 0.0165 to 0.5 m.m. / rev. of spindle
ELECTRICALS :
Electric Motor of 3 H.P. / 2.25 k.w., 3 Phase, 50 Hz, 440 V., 1440 RPM with Reverse-Forward switch, V-Belt, Electrical Wirings and fittings.
IMPORTANT :
Any Change in Specifications of the machine like center height, width of bed, hollow of spindle etc. Will be provided as per requirements at extra cost.
NOTE :
As improvements are constantly made in our machines, the above illustrations, specifications, dimensions and technical data are subject to modifications and change without prior notice and not binding on us.
